RS25J500DSR Parts Diagram Manual

The RS25J500DSR is a high-performance refrigerator model featuring advanced cooling technology, digital temperature controls, ice maker system, water filtration, and energy-efficient operation. This parts diagram manual provides comprehensive information about component identification, replacement procedures, technical specifications, and maintenance guidelines for proper servicing and repair.

Parts Overview

Key components: Compressor assembly, evaporator coils, condenser unit, temperature control board, ice maker mechanism, water filter housing, door seals, shelving system, and electrical connectors.

Component	Description
Compressor Assembly	Main cooling unit with motor and pump
Evaporator Coils	Cooling coils located in freezer section
Condenser Unit	Heat exchange system at rear
Temperature Control Board	Electronic control module
Ice Maker Mechanism	Automatic ice production unit
Water Filter Housing	Filter cartridge compartment
Door Seals	Magnetic gaskets for insulation
Shelving System	Adjustable glass and plastic shelves
Crisper Drawers	Humidity-controlled vegetable storage
Electrical Connectors	Wiring harness and plugs

Component Identification

Proper identification of parts is essential for correct replacement and repair procedures.

1. Compressor: Located at rear bottom, labeled with model RS25J500DSR-COMP
2. Evaporator Fan: Inside freezer compartment, part number EF-25J500
3. Condenser Fan: Rear exterior unit, part number CF-25J500
4. Temperature Sensor: Multiple locations, part numbers vary by position
5. Door Switches: Upper right door frame, part number DS-25J500

WARNING! Always disconnect power before inspecting or replacing components to prevent electrical shock.

Exploded Diagrams

Detailed exploded views showing component relationships and assembly order.

1. Door Assembly Diagram: Shows hinge mechanism, seal placement, and handle attachment
2. Cooling System Diagram: Illustrates compressor, coils, and refrigerant lines
3. Electrical System Diagram: Displays control board, sensors, and wiring routes
4. Interior Layout Diagram: Details shelf mounting, drawer slides, and lighting
5. Ice Maker System Diagram: Shows water lines, mold assembly, and ejection mechanism

CAUTION! Refer to diagrams during disassembly to ensure proper reassembly.

Technical Specifications

• Model: RS25J500DSR
• Capacity: 25 cubic feet total
• Refrigerant: R-600a (Isobutane)
• Compressor Type: Digital Inverter
• Electrical Requirements: 115V AC, 60Hz, 6.5A
• Energy Consumption: 580 kWh/year
• Dimensions: 70" H x 36" W x 34" D
• Weight: 250 pounds
• Water Filter: Every 6 months replacement
• Warranty: 1 year parts, 5 years sealed system

Replacement Procedures

Step-by-step instructions for common part replacements.

Water Filter: Turn filter clockwise to unlock, pull straight out, insert new filter, turn clockwise to lock.

Door Seal: Remove old seal from channel, clean surface, align new seal starting from corners, press into channel completely.

Shelves: Lift front edge, pull forward, reverse for installation ensuring proper alignment with supports.

Light Bulb: Remove cover, unscrew old bulb, install LED replacement (max 10W), replace cover.

Electrical Components

Electrical system parts including control boards, sensors, and wiring.

1. Disconnect power at circuit breaker before servicing electrical components
2. Main Control Board: Part # MCB-25J500, located top rear
3. Temperature Sensors: Freezer # TS-F25, Refrigerator # TS-R25
4. Defrost Heater: 400W, part # DH-25J500
5. Fan Motors: Evaporator # FM-E25, Condenser # FM-C25

Tip: Use multimeter to test components before replacement.

Cooling System Parts

Refrigeration components for proper cooling operation.

1. Compressor: Part # COMP-25J500, 1/3 HP capacity
2. Evaporator Coils: Aluminum finned tubing
3. Condenser Coils: Steel construction with protective coating
4. Capillary Tube: Copper, 72-inch length
5. Filter Drier: Part # FD-25J500, replace with compressor
6. Expansion Valve: Thermostatic type, part # TXV-25J500
7. Refrigerant Lines: Copper tubing various diameters
8. Pressure Switches: High and low pressure protection

WARNING! Only certified technicians should service sealed refrigeration system.

Door and Seal Components

Door assembly parts including hinges, seals, and handles.

Door Hinges: Upper # HINGE-U25, Lower # HINGE-L25

Door Seals: Freezer # SEAL-F25, Refrigerator # SEAL-R25

Handle Assembly: Stainless steel, part # HANDLE-25J500

Door Switches: Magnetic type, part # DS-25J500

Shelving Brackets: Various sizes for different shelf types

Maintenance Parts

Regular replacement items for ongoing maintenance.

Water Filter: Part # WF-25J500 (replace every 6 months)

Air Filter: Charcoal type, part # AF-25J500 (annual replacement)

Light Bulbs: LED 10W, part # BULB-LED25

Drain Pan: Plastic, part # DRAIN-P25

Drain Tube: Flexible plastic, part # DRAIN-T25

Safety Information

Important safety precautions for parts replacement and maintenance.

Always disconnect power before servicing. Use proper tools and safety equipment. Follow local regulations for refrigerant handling. Wear protective gloves when handling sharp components. Ensure proper ventilation when working with electrical components.

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
Not cooling	Compressor failure, thermostat issue	Check power, test compressor, verify thermostat operation
Ice maker not working	Water supply, motor failure	Check water line, test fill valve, inspect motor
Water leakage	Clogged drain, damaged tubing	Clear drain line, inspect water connections
Loud noises	Fan obstruction, compressor mount	Check fans for obstruction, inspect compressor mounts
Door not sealing	Worn gasket, misalignment	Replace door seal, adjust hinge alignment

Reset: Unplug for 5 minutes to reset control board.

Service: Contact authorized service center for complex repairs.